Racing clip-ons for motorcycle | made by Melotti Racing Italy

#SM1250

#SM1250

The tall bracelet (45 mm), together with the boring of the internal hole, get a high grip on the fork sleeve and therefore to use a lower tightening torque for the bracelet, ensuring the optimal functioning of the fork in the lunge phase (braking).

GP-type bracelet-bar front coupling system (cone-shaped) to obtain a high rigidity and minimum external encumbrance.
This choice offers possibility to use the entire length of the bar for the assembly of the controls.

Predetermined collapse section to avoid, in case of break of the bar due to a fall, the overloading of the fork sleeve which would irretrievably damage the internal hydraulics too.

The handlebar is also designed with an anti-rotation and anti-slip system.
This solution guarantees maximum safety and allows the quick and precise positioning of levers and buttons for teams that use the pre-assembled controls on the bars, whenever it is necessary to disassemble the bar from the bracelet after a fall.

Vernier to adjust the opening angle of the handlebars.
The combined use of these GP clip-ons with Melotti Racing top yoke makes the adjustment extremely easy and quick without the use of special masks.

Two stainless steel screws for fastening the bracelet.

A vernier on the outer end of the bar is helpful in case you need to shorten its length.

- Inclination angle 7°
- Advancement offset 20 mm
- Tube length 240 mm
- Exploitable length 240 mm
- Tube external diameter 22 mm
- Tube internal diameter 16.5 mm.
- To fit on forks with external diameter 50 mm.

#SM1251

#SM1251

The tall bracelet (45 mm), together with the boring of the internal hole, get a high grip on the fork sleeve and therefore to use a lower tightening torque for the bracelet, ensuring the optimal functioning of the fork in the lunge phase (braking).

GP-type bracelet-bar front coupling system (cone-shaped) to obtain a high rigidity and minimum external encumbrance.
This choice offers possibility to use the entire length of the bar for the assembly of the controls.

Predetermined collapse section to avoid, in case of break of the bar due to a fall, the overloading of the fork sleeve which would irretrievably damage the internal hydraulics too.

The handlebar is also designed with an anti-rotation and anti-slip system.
This solution guarantees maximum safety and allows the quick and precise positioning of levers and buttons for teams that use the pre-assembled controls on the bars, whenever it is necessary to disassemble the bar from the bracelet after a fall.

Vernier to adjust the opening angle of the handlebars.
The combined use of these GP clip-ons with Melotti Racing top yoke makes the adjustment extremely easy and quick without the use of special masks.

Two stainless steel screws for fastening the bracelet.

A vernier on the outer end of the bar is helpful in case you need to shorten its length.

- Inclination angle 7°
- Advancement offset 20 mm
- Tube length 240 mm
- Exploitable length 240 mm
- Tube external diameter 22 mm
- Tube internal diameter 16.5 mm.
- To fit on forks with external diameter 51 mm.

#SM1252

#SM1252

The tall bracelet (45 mm), together with the boring of the internal hole, get a high grip on the fork sleeve and therefore to use a lower tightening torque for the bracelet, ensuring the optimal functioning of the fork in the lunge phase (braking).

GP-type bracelet-bar front coupling system (cone-shaped) to obtain a high rigidity and minimum external encumbrance.
This choice offers possibility to use the entire length of the bar for the assembly of the controls.

Predetermined collapse section to avoid, in case of break of the bar due to a fall, the overloading of the fork sleeve which would irretrievably damage the internal hydraulics too.

The handlebar is also designed with an anti-rotation and anti-slip system.
This solution guarantees maximum safety and allows the quick and precise positioning of levers and buttons for teams that use the pre-assembled controls on the bars, whenever it is necessary to disassemble the bar from the bracelet after a fall.

Vernier to adjust the opening angle of the handlebars.
The combined use of these GP clip-ons with Melotti Racing top yoke makes the adjustment extremely easy and quick without the use of special masks.

Two stainless steel screws for fastening the bracelet.

A vernier on the outer end of the bar is helpful in case you need to shorten its length.

- Inclination angle 7°
- Advancement offset 20 mm
- Tube length 240 mm
- Exploitable length 240 mm
- Tube external diameter 22 mm
- Tube internal diameter 16.5 mm.
- To fit on forks with external diameter 52 mm.

#SM1150

The tall bracelet (45 mm), together with the boring of the internal hole, get a high grip on the fork sleeve and therefore to use a lower tightening torque for the bracelet, ensuring the optimal functioning of the fork in the lunge phase (braking).

GP-type bracelet-bar front coupling system (cone-shaped) to obtain a high rigidity and minimum external encumbrance.
This choice offers possibility to use the entire length of the bar for the assembly of the controls.

Predetermined collapse section to avoid, in case of break of the bar due to a fall, the overloading of the fork sleeve which would irretrievably damage the internal hydraulics too.

The handlebar is also designed with an anti-rotation and anti-slip system.
This solution guarantees maximum safety and allows the quick and precise positioning of levers and buttons for teams that use the pre-assembled controls on the bars, whenever it is necessary to disassemble the bar from the bracelet after a fall.

Vernier to adjust the opening angle of the handlebars.
The combined use of these GP clip-ons with Melotti Racing top yoke makes the adjustment extremely easy and quick without the use of special masks.

Two stainless steel screws for fastening the bracelet.

A vernier on the outer end of the bar is helpful in case you need to shorten its length.

- Inclination angle 7°
- Advancement offset 20 mm
- Tube length 240 mm
- Exploitable length 240 mm
- Tube external diameter 22 mm
- Tube internal diameter 16.5 mm.
- To fit on forks with external diameter 50 mm.

#SM1151

The tall bracelet (45 mm), together with the boring of the internal hole, get a high grip on the fork sleeve and therefore to use a lower tightening torque for the bracelet, ensuring the optimal functioning of the fork in the lunge phase (braking).

GP-type bracelet-bar front coupling system (cone-shaped) to obtain a high rigidity and minimum external encumbrance.
This choice offers possibility to use the entire length of the bar for the assembly of the controls.

Predetermined collapse section to avoid, in case of break of the bar due to a fall, the overloading of the fork sleeve which would irretrievably damage the internal hydraulics too.

The handlebar is also designed with an anti-rotation and anti-slip system.
This solution guarantees maximum safety and allows the quick and precise positioning of levers and buttons for teams that use the pre-assembled controls on the bars, whenever it is necessary to disassemble the bar from the bracelet after a fall.

Vernier to adjust the opening angle of the handlebars.
The combined use of these GP clip-ons with Melotti Racing top yoke makes the adjustment extremely easy and quick without the use of special masks.

Two stainless steel screws for fastening the bracelet.

A vernier on the outer end of the bar is helpful in case you need to shorten its length.

- Inclination angle 7°
- Advancement offset 20 mm
- Tube length 240 mm
- Exploitable length 240 mm
- Tube external diameter 22 mm
- Tube internal diameter 16.5 mm.
- To fit on forks with external diameter 51 mm.

#SM1152

The tall bracelet (45 mm), together with the boring of the internal hole, get a high grip on the fork sleeve and therefore to use a lower tightening torque for the bracelet, ensuring the optimal functioning of the fork in the lunge phase (braking).

GP-type bracelet-bar front coupling system (cone-shaped) to obtain a high rigidity and minimum external encumbrance.
This choice offers possibility to use the entire length of the bar for the assembly of the controls.

Predetermined collapse section to avoid, in case of break of the bar due to a fall, the overloading of the fork sleeve which would irretrievably damage the internal hydraulics too.

The handlebar is also designed with an anti-rotation and anti-slip system.
This solution guarantees maximum safety and allows the quick and precise positioning of levers and buttons for teams that use the pre-assembled controls on the bars, whenever it is necessary to disassemble the bar from the bracelet after a fall.

Vernier to adjust the opening angle of the handlebars.
The combined use of these GP clip-ons with Melotti Racing top yoke makes the adjustment extremely easy and quick without the use of special masks.

Two stainless steel screws for fastening the bracelet.

A vernier on the outer end of the bar is helpful in case you need to shorten its length.

- Inclination angle 7°
- Advancement offset 20 mm
- Tube length 240 mm
- Exploitable length 240 mm
- Tube external diameter 22 mm
- Tube internal diameter 16.5 mm.
- To fit on forks with external diameter 52 mm.