|
|||||||||||||||||||||||||||||||||||||||||||||||||||
| MXL wide display dash loggers for motorbikes (made by AIM - Italy) | ||||
| MXL is a powerful, professional and high-tech gauge which allows the user to sample and display a large number of parameters. MXL includes a tachometer, 1 RPM input, 8 to 12 analog inputs (temperatures, pressures, potentiometers, accelerometers, gyros, lambdas, "on-board" and custom sensors), 1 to 4 speed input, gear and lap time.
With a beautiful and wide display, MXL has got a backlight and a high speed USB data download to a PC: these data may be analysed with the powerful Race Studio 2 software. It can be a part of a network of AIM products such as (see through) GPS module, lambda controllers LCU-ONE or DaVid video system.
It can be easily connected through CAN or RS232 to an existing ECU to enable a huge amount of extra channels.
MXL versions - Strada (same as Pista, no sampling capability) - Pista (1 speed, 8 analog inputs, AMP connectors) - Pro (4 speeds, 12 analog inputs). Specifications - Dimensions: 174*110 mm - Display dimensions 140*67 mm - External 9 - 24 V power supply - From 128 kb to 16 MB non-volatile internal memory. Features - Water resistant, extra-wide display with backlight - Rugged and lightweight aluminium chassis - RPM graphical and numerical view - Configurable RPM scaling (from 4.000 to 20.000? end of scale) - Gear number: calculated or sampled from "on-board" sensor - CAN protocol for external "expansion modules" - 10 shift lights: Green - Yellow - Red - 6 freely configurable max/min alarm lights - Lap times - configurable Split times, through infrared RX TX - Internal data acquisition system with 8 MB non volatile memory - Up to 2 kHz sampling (200 Hz for single channel) - Total and partial (resettable) odometer - Can do track mapping using internal lateral g-sensor or our powerful GPS module. |
 Easy-to-read, wide, backlighted display  Everything under control at a glance...
|
|||
| MXL Strada wide display dash logger Memorizes up to 250 rev. with: - 5 split-times - lowest and highest peaks of revolutions - speed - 2 channels at your choice Sensors kit, and lap time receiver and transmitter are not provided. Strada MXL display is provided with handbook explaining in details how to proceed to the bike connections. Weight Kg 0.86
Delivery in 5-10 days from your order. |
 #X10MXLS |
MXL Pista wide display dash logger If you’re a driver, aiming to your best lap, you will find in the MXL Pista a valuable help to analyse and optimise both your and your vehicle’s performances. Featuring 8 Megabytes of internal memory, 8 configurable channels, kit’s sensors and infrared transmitters and receivers, MXL Pista is what you are searching for. Electrical connection to stock bike is not needed, except supply. Weight Kg 1.25
Delivery in 5-10 days from your order. |
 #X10MXLC |
|||||||||||||||||||
| MXL Pro 05 wide display dash logger If you’re looking for excellence, the most performing data acquisition system, MXL Pro has everything you need to bring you on the top of the podium. Featuring Deutsche Connectors, 16 Megabytes of internal memory, 4 speed channels, 12 configurable channels, kit’s sensors and infrared transmitters and receivers, MXL Pro is your ultimate choice. Electrical connection to stock bike is not needed, except supply. Weight Kg 1.07
Delivery in 5-10 days from your order. |
 #X10MXLP |
GPS Pista optional module We often think that GPS modules are useful for map-tracking purposes only but the GPS can be used to acquire much more important data: from brakes analysis to chassis info and, obviously, driver's behaviour while on track. Thanks to the GPS module, you will be able to visualize track data with speed, position (including driver's errors) and visualize all those information in Google Earth. All of your performances on the track viewed through real, stunning images. This is all you need to improve your driving skills and start tuning your car! The GPS module is connectable and perfectly compatible with other AIM products such MXL professional gauge or EVO 3 data logger. Information you'll get thanks to GPS module: * Position * Speed * Cornering rate * Cornering in-line and lateral G * Lap times. To be used as optional of the wide display dash logger MXL Pista #X10MXLC. Weight Kg 0.18
Delivery in 5-10 days from your order. |
 #X40GPS3D120M |
|||||||||||||||||||
| GPS Pro optional module We often think that GPS modules are useful for map-tracking purposes only but the GPS can be used to acquire much more important data: from brakes analysis to chassis info and, obviously, driver's behaviour while on track. Thanks to the GPS module, you will be able to visualize track data with speed, position (including driver's errors) and visualize all those information in Google Earth. All of your performances on the track viewed through real, stunning images. This is all you need to improve your driving skills and start tuning your car! The GPS module is connectable and perfectly compatible with other AIM products such MXL professional gauge or EVO 3 data logger. Information you'll get thanks to GPS module: * Position * Speed * Cornering rate * Cornering in-line and lateral G * Lap times. To be used as optional of the wide display dash logger MXL Pro #X10MXLP. Weight Kg -
Delivery in 5-10 days from your order. |
 #X40GPS3D120P |
LCU-One optional lambda controller with analog interface LCU-One uses a wide band Bosch LSU 4.9 sensor and measures Lambda values from 0.65 to 1.6: this allows a much more accurate monitoring, which leads to a better setup of your engine, and in particular of your injection. LCU-One provides both analog and digital (CAN) linear outputs. Thanks to CAN bus line, up to 12 controllers can be connected, to optimize injection in every single cylinder. This allows to analyze air / fuel Ratio, Lambda value, sensor temperature and diagnostics. A dedicated software can be used to configure the module and for receiving the data directly on the PC. Features: LCU-One permits to configure (through dedicated software): • stoichiometric A/F value according to fuel type • lambda value or air / fuel Ratio units • analog voltage outputs (min / max end of scale within 0-5 Volt) • analog and RS232 outputs • includes: RS232 analog cable, CD, Bosch 4.9 lambda probe and analog cable (to be defined between: V02359050, V02359060 or V023599070). Weight Kg 0.41
Delivery in 5-10 days from your order. |
 #X08LCUKAORS0 |
|||||||||||||||||||
| LCU-One optional lambda controller with CAN interface LCU-One uses a wide band Bosch LSU 4.9 sensor and measures Lambda values from 0.65 to 1.6: this allows a much more accurate monitoring, which leads to a better setup of your engine, and in particular of your injection. LCU-One provides both analog and digital (CAN) linear outputs. Thanks to CAN bus line, up to 12 controllers can be connected, to optimize injection in every single cylinder. This allows to analyze air / fuel Ratio, Lambda value, sensor temperature and diagnostics. A dedicated software can be used to configure the module and for receiving the data directly on the PC. Features: LCU-One permits to configure (through dedicated software): • stoichiometric A/F value according to fuel type • lambda value or air / fuel Ratio units • analog voltage outputs (min / max end of scale within 0-5 Volt) • CAN and RS232 outputs • includes: CAN line terminator, CD, Bosch 4.9 lambda probe and CAN cable (to be defined between: V02359090, V02359110 or V02359100). Weight Kg -
Delivery in 5-10 days from your order. |
 #X08LCUKCRS00 |
LCU-One optional lambda controller with analog and CAN interfaces LCU-One uses a wide band Bosch LSU 4.9 sensor and measures Lambda values from 0.65 to 1.6: this allows a much more accurate monitoring, which leads to a better setup of your engine, and in particular of your injection. LCU-One provides both analog and digital (CAN) linear outputs. Thanks to CAN bus line, up to 12 controllers can be connected, to optimize injection in every single cylinder. This allows to analyze air / fuel Ratio, Lambda value, sensor temperature and diagnostics. A dedicated software can be used to configure the module and for receiving the data directly on the PC. Features: LCU-One permits to configure (through dedicated software): • stoichiometric A/F value according to fuel type • lambda value or air / fuel Ratio units • analog voltage outputs (min / max end of scale within 0-5 Volt) • analog, CAN and RS232 outputs • includes: CAN line terminator, CD, Bosch 4.9 lambda probe and analog cable (to be defined between: V02359090, V02359110 or V02359100) and CAN cable (to be defined between: V02359090, V02359110 or V02359100). Weight Kg -
Delivery in 5-10 days from your order. |
 #X08LCUKAOCRS |
|||||||||||||||||||
| MemoryKey MemoryKey is a very useful tool that allows an immediate storage of data acquired by AIM MXL loggers during test and race sessions as well as their transfer on a PC, where they will be analysed with the powerful Race Studio 2 software. With 32 Mb internal memory, MemoryKey can store data concerning different sessions. Weight Kg 0.03
Delivery in 5-10 days from your order. |
 #X50MEPC00 |
Optional transmitter for MXL Strada #X10MXLS IR lap marker transmitter. Transmitter only included. Receiver not included. Supply 8-16 V DC ((external or by 8 AA internal batteries not included). Sizes 124 x 40 x 39 mm. Weight Kg 0.21
Delivery in 5-10 days from your order. |
 #X02TXKMA01 |
|||||||||||||||||||
| Optional receiver for MXL Strada #X10MXLS IR lap marker receiver. Weight Kg 0.04
Delivery in 5-10 days from your order. |
 #X02RXM3040 |
Optional sensors kit for MXL Strada #X10MXLS Cables with RPM, speed and water temperature sensors. Weight Kg -
Delivery in 5-10 days from your order. |
 #X10MXLKS00000 |
|||||||||||||||||||
| Sensor for water/oil temperature Thermoresistor with M5 thread for water or oil temperature. To be used with #X10MXLS, #X10MXLC or #X10MXLP. Weight Kg -
Delivery in 5-10 days from your order. |
#3CVTRES2K0 |
Sensor for water/oil temperature Thermoresistor PT100 - 1/8 NPTV for water or oil temperature. To be used with #X10MXLS, #X10MXLC or #X10MXLP. Weight Kg -
Delivery in 5-10 days from your order. |
#3CVTRRNPT2K |
|||||||||||||||||||
| Sensor for water/oil temperature Thermoresistor PT100 with M10 thread for water or oil temperature. To be used with #X10MXLS, #X10MXLC or #X10MXLP. Weight Kg -
Delivery in 5-10 days from your order. |
#3CVTRM1003C2K |
Sensor for water/oil temperature Thermocouple with M5 thread for water or oil temperature. To be used with #X10MXLS, #X10MXLC or #X10MXLP. Weight Kg -
Delivery in 5-10 days from your order. |
#3CVGAS802 |
|||||||||||||||||||
| Spare supply cable For AIM transmitters. Weight Kg -
Delivery in 5-10 days from your order. |
#V02POWTX0 |
|||||||||||||||||||||
|
|||||||||||||||||||||||||
|
|||||||||||||||||||||||||
